MTD Gold 769-04179 Snow Blower Owners Manual

6
Maintaining
Your Snow
Thrower
Lubrication
Drive and Shifting Mechanism
At least once a season or after every 25 hours of opera-
tion, remove rear cover. Lubricate any chains, sprockets,
gears, bearings, shafts, and the shifting  mechanism at
least once a season. Use engine oil or a spray lubricant.
Refer to Figure 6-1.
Gear
(Hex)
Shaft
FWrihcetieoln
IMPORTANT:friction wheel andKeepdriveall greaseplate.   and oil off the rubber
Wheels
At least once a season, remove wheels. Clean and coat
the axles with a multipurpose automotive grease before
reinstalling wheels.
Drive
Plate
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around  the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 6-2.
Figure 6-1
WARNING
Augers
Grease
Shear Pin
Vent Plug
•  The augers are secured to the spiral shaft with shear
pins and cotter pins. If the auger should strike a
foreign object or ice jam, the snow thrower is designed
so that the pins may shear. See Figure 6-2.
Before lubricating,
Fitting (optional)
repairing or
Auger Shaft
inspecting, disengage
all controls and stop
engine.  Wait until all
moving parts have
come to a complete
stop. Remove the
safety key to prevent
unintended firing of
the engine.
If the augers will not turn, check to see if the pins have
sheared. Replacement shear pins have been provided
with the snow thrower. When replacing pins, spray an
oil lubricant into shaft before inserting new pins.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when  necessary.
To remove skid shoes:
Cotter Pin
Spacers
Bearing
Figure 6-2
1.
Remove the carriage bolts (and washers if
equipped)and hex flange  nuts which secure the skid
shoes to the snow thrower.
2.
Reassemble new skid shoes with previously removed
hardware. Refer to Figure 6-3.
To remove shave plate:
1.
Remove the carriage bolts and hex nuts which attach
IMPORTANT
Avoid oil spillage on
rubber friction wheel
and aluminum drive
plate.
it and the skid shoes to the snow thrower housing.
2.
Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
Replacing Belts
To remove and replace either the auger belt or the drive
belt, follow the steps below and then proceed to the
specific steps listed under respective sub-headings.
Figure 6-3
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance and lubrication  instruc-
tions.
1.  Disconnect  the chute crank assembly at the discharge
chute end by removing the hairpin clip and the flat
washer. See Figure 6-8.
16
Product Specification
CategoriesGold Snow Blower Manuals, MTD Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 56 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website