|Categories||Carrier HVAC Manuals, HVAC Heating Ventilating Air Conditioning Manuals|
|Product Brand||Support Phone Number: In North America, please call 1-800-CARRIER for immediate customer assistance from 8:00a -5:00p (EST) weekdays, Heating, Ventilating and Air Conditioning - HVAC|
|Document File Type|
|Wikipedia's Page||Carrier Corporation|
58UHV, 58UXV Upflow/Horizontal Variable-Speed, 2-Stage Induced-Combustion Gas Furnaces Visit www.carrier.com Installation, Start-Up, and Operating Instructions Sizes 060-120, Series 110 NOTE: Read the entire instruction manual before starting the installation. This symbol indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS .1 DIMENSIONAL DRAWING 2 ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCEDURE .2 CLEARANCES TO COMBUSTIBLES 3 INTRODUCTION .3-4 LOCATION 4 General 4 Location Relative to Cooling Equipment 4 Hazardous Locations .4 AIR FOR COMBUSTION AND VENTILATION .4-5 Unconfined Space .4 Confined Space 4-5 INSTALLATION 6-11 Upflow Installation .6 Horizontal Attic Installation .6 Horizontal Crawlspace Installation 6 Filter Arrangement 6-8 Leveling Legs (If Required For Upflow) 8 Gas Piping 8-9 Electrical Connections .9-10 115-v Wiring 9 24-v Wiring 9-10 Accessories 10 Venting .10-11 START-UP, ADJUSTMENT, AND SAFETY CHECK 11-23 General 11 Sequence of Operation 11-16 Adaptive Heating Mode .12-14 Non-Adaptive Heating Mode 14 Cooling Mode 14 Continuous Blower Mode .14 Heat Pump Mode .14-15 Defrost Mode .15 Set-Up Procedures .15-16 Start-Up Procedures .16-18 Adjustments .18-23 Set Gas Input Rate .18-22 Set Air Temperature Rises .22-23 Set Thermostat Heat Anticipator 23 Check Safety Controls 23 Checklist 23 ama CANADIAN GAS ASSOCIATION ® A PP R O VED R CERTIFICATION OF MANUFACTURING SITE SAFETY CONSIDERATIONS Installation and servicing of heating equipment can be hazardous due to gas and electrical components.
Only trained and qualified personnel should install, repair, or service heating equipment. Untrained personnel can perform basic maintenance functions such as cleaning and replacing air filters. All other operations must be performed by trained service personnel. When working on heating equipment, observe precautions in the literature, on tags, and on labels attached to or shipped with the unit and other safety precautions that may apply. Follow all safety codes. In the United States, refer to the National Fuel Gas Code (NFGC) NFPA No. 54-1996/ANSI Z223.1-1996. In Canada, refer to the current edition of the National Standard of Canada CAN/CGA- B149.1- and .2-M95 Natural Gas and Propane Installation Codes (NSCNGPIC). Wear safety glasses and work gloves. Have fire extinguisher available during start-up and adjustment procedures and service calls. Recognize safety information. This is the safety-alert symbol. When you see this symbol on the furnace and in instructions or manuals, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies a hazard which could result in personal injury or death. CAUTION is used to identify unsafe practices which would result in minor personal injury or product and property damage. These instructions cover minimum requirements and conform to existing national standards and safety codes. In some instances, these instructions exceed certain local codes and ordinances, especially those that may not have kept up with changing residential construction practices. We require these instructions as a minimum for a safe installation. Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.