MTD 5DM Series Log Splitter Lawn Mower Owners Manual

5
Maintaining
Your Log
Splitter
Hydraulic Fluid
Check the hydraulic fluid level in the log splitter
reservoir tank before each use. Maintain fluid level to
just below the oil plug.
Have the hydraulic fluid in the reservoir changed every
100 hours of operation. See your authorized service
dealer to have the hydraulic fluid changed.
Beam and Splitting Wedge
Lubricate top and bottom of the beam (where it comes
into contact with the cylinder), before each use, with
engine oil.
Hose Clamps (If Equipped)
Check, before each use, if hose clamps on the suction
hose (attached to the side of the pump)  are tight.
Check the hose clamps on the return hose at least
once a season.
Figure 5-1
WARNING
Do not at any time
Engine
Refer to the Engine maintenance section for all mainte-
nance instructions.
WARNING: Before cleaning,
lubricating, repairing, or inspecting,
disengage the control lever and stop
engine. Disconnect the spark  plug
make any adjustments
without first stopping
engine, disconnecting
spark plug wire, and
grounding it against
the engine. Always
wear safety glasses
during operation or
while performing any
adjustments or repairs.
Changing the Belt
wire and ground it against the engine to prevent
unintended starting. Always wear  safety glasses
during operation or while performing  any adjust-
ments or repairs.
WARNING: Be sure to shut the engine
off, disconnect the spark plug wire(s)
and ground against the engine to
prevent unintended starting before
removing the belt.
Conditions that Will Void Warranty
1.
2.
Failure to maintain proper fluid level in reservoir
Changing the relief valve setting or pressure adjust-
ment of control valve without proper knowledge and
instruction from the factory
Thebe replacedbelt on yourif anylogsignssplitterof wearis subjectare present.to wear and should
Higher pressure could
cause the hoses to
burst, cylinder to rup-
ture, and intense fluid
to be released, which
could result in serious
personal injury.
IMPORTANT: The V-belt found on your log splitter is a
non-clutching, constant tension  belt. A substitute (non-
OEM) V-belt can be dangerous. For a proper working
machine, use factory approved belts.
Toas follows:change or replace the belt on your log splitter, proceed
WARNING: Higher pressure  could
cause the hoses to burst, cylinder
to rupture, and intense fluid to be
released, which could result in serious  personal
injury.
NOTE: This procedure requires the assistance  of a
3.
4.
5.
Disassembling the pump
second person.
Use of incorrect hydraulic fluid
1.
2.
3.
4.
Place the unit in the transport position  on level ground
Lack of lubrication or improper lubrication  of the
as shown in Figure 5-1.
beam or unit
Disconnectthe engine. the spark plug wire and ground it  against
6.
7.
Excessive heating of the hydraulic system
Attempting to start unit in temperatures under 20°F
Drain gasoline or place a piece of plastic beneath  the
without pre-heating fluid in reservoir
gas cap to prevent gasoline leakage.
8.
Unattended leaks in hydraulic system
Remove the belt cover by removing the six self-tap-
ping screws that fasten it to the frame. See Figure 5-1.
1
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 52 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website