MTD Troy-Bilt 60T Transmatic Tractor Lawn Mower Owners Manual

6
Maintaining
Your Lawn
Tractor
Cutting Blades
WARNING: Be sure to shut the
engine off, remove ignition key,
disconnect the spark plug wire(s)
and ground against the engine
to prevent unintended starting
before removing the cutting
blade(s) for sharpening or
replacement. Protect your hands
by using heavy gloves or a rag to
grasp the cutting blade.
WARNING: Periodically inspect
the blade spindles for cracks or
damage, especially if you strike a
foreign object. Replace immedi-
ately if damaged.
Figure 6-
T1.he blades may be removed as follows:
WARNING
Remove the deck from beneath the tractor, (refer to
Cutting Deck Removal) then gently flip the  deck over
to expose its underside.
Place a block of wood between the center deck hous-
Be sure to shut the
engine off, remove ig-
nition key, disconnect
the spark plug wire(s)
and ground against
the engine to prevent
unintended starting
before removing
Use a 15/16” wrench to remove the hex flange nut
4.
To properly sharpen the cutting blades,  remove equal
amounts of metal from both ends of the blades along
the cutting edges, parallel to the trailing  edge, at a
 �INCH
the cutting blade(s)
for sharpening or
25°
to 30° angle.
Figure 6-6
replacement. Protect
your hands by using
heavy gloves or a rag
to grasp the cutting
blade.
IMPORTANT: If the cutting edge of the blade has already    Fuses
been sharpened to within 1-5/8”  from the edge, or if any
metal separation is present, replace the blades with  new
ones. See Figure 6-6.
A fuse is installed in your tractor’s wiring harness to
protect the tractor’s electrical system from damage
caused by excessive amperage.
If the electrical system does not function,  or your
tractor’s engine will not crank, first check to be certain
that the fuse has not blown.
It can either be found under the hood mounted behind
the top of the dash panel on the support  bar, or under
the seat mounted to the inside of the tractor frame
next to the battery tray.
WARNING: Always use a fuse
with the same amperage capacity
for replacement.
It is important that each cutting  blade edge be ground
equally to maintain proper blade balance.
Periodically inspect
the blade spindles for
cracks or damage,
especially if you strike
a foreign object.
When replacing the blade, be sure to install the blade
with the side of the blade marked ‘‘Bottom’’  (or with
a part number stamped in it) facing the  ground when
the mower is in the operating position.
IMPORTANT: Use a torque wrench to tighten the blade
spindle hex flange nut to between 70 foot-pounds and  90
foot-pounds.
Replace immediately if
damaged.
Always use a fuse with
the same amperage
capacity for replace-
ment.

Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 64 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(1 votes, average: 3 out of 3)
Lawn and Garden readers have rated MTD Troy-Bilt 60T Transmatic Tractor Lawn Mower Owners Manual 3.0 out of 3.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

MTD Troy-Bilt 60T Transmatic Tractor Lawn Mower Owners Manual SKU UPC Model
Ronald Hardy on Apr 03, 2016. MTD 60T, Troy-Bilt 60T

I have just obtained this mower so I can't really rate the mower.


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website