| Categories | Computer Equipment, Copier Manuals, Printer Manuals, Toshiba Copier Manuals, Toshiba Printer Manuals |
|---|---|
| Tags | Toshiba E-Studio GL-1010 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
GL-1010 Operator’s Guide (Basic) Version 1.2.9 Your guide to using the Toshiba e-STUDIO GL-1010 Electronic Document Processing System GL-1010 Operator’s Guide (Basic) 1 2 GL-1010 Operator’s Guide (Basic) G L – 1 0 1 0 O p e r at o r ‘s G u i d e (Basic) Your guide to using the Toshiba e-STUDIO GL-1010 Electronic Document Processing System GL-1010 Operator’s Guide (Basic) 3 END USER SOFTWARE LICENSE AGREEMENT INSTALLING OR OTHERWISE USING THIS SOFTWARE PRODUCT CONSTITUTES YOUR ACCEPTANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEPARATE LICENSE IS PROVIDED BY THE SUPPLIER OF APPLICABLE SOFTWARE IN WHICH CASE SUCH SEPARATE LICENSE SHALL APPLY).
User Manual Free Download. Operator’s Printer Manual Guide. Free Printer/Copier Manual Download PDF.
IF YOU DO NOT ACCEPT THESE TERMS, YOU MAY NOT INSTALL OR USE THIS SOFTWARE, AND YOU MUST PROMPTLY RETURN THE SOFTWARE TO THE LOCATION WHERE YOU OBTAINED IT. GRANT OF LICENSE: This is a legal agreement between you, the end-user ( “You “), and TOSHIBA TEC Corporation ( “TTEC “) and its suppliers. This software, fonts (including their typefaces) and related documentation ( “Software “) is licensed for use with the system CPU on which it was installed ( “System “) in accordance with the terms contained in this Agreement. This Software is proprietary to TTEC and/or its suppliers. TTEC and its suppliers disclaim responsibility for the installation and/or use of this Software, and for the results obtained by using this Software. You may use one copy of the Software as installed on a single System, and may not copy the Software for any reason except as necessary to use the Software on a single System. Any copies of the Software shall be subject to the conditions of this Agreement. You may not, nor cause or permit any third party to, modify, adapt, merge, translate, reverse compile, reverse assemble, or reverse engineer the Software. You may not use the Software, except in accordance with this license. No title to the intellectual property in the Software is transferred to you and full ownership is retained by TTEC or its suppliers. Source code of the Software is not licensed to you. You will be held legally responsible for any infringement, unauthorized transfer, reproduction or use of the Software or its documentation. TERM: This license is effective until terminated by TTEC or upon your failure to comply with any term of this Agreement. Upon termination, you agree to destroy all copies of the Software and its documentation. You may terminate this license at any time by destroying the Software and its documentation and all copies. DISCLAIMER OF WARRANTY: This Software is provided “AS IS ” without warranty of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability, fitness for a particular purpose, title, and non-infringement. TTEC and its suppliers disclaim any warranty relating to the quality and performance of the Software. If the Software proves defective, You (and not TTEC or its suppliers) shall be responsible for the entire cost of all necessary servicing, repair or correction. TTEC and its suppliers do not warrant that the functions contained in the Software will meet your requirements or that the operation of the Software will be uninterrupted or error free. LIMITATION OF LIABILITY: IN NO EVENT WILL TTEC OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY DAMAGES, WHETHER IN CONTRACT, TORT, OR OTHERWISE (except personal injury or death resulting from negligence on the part of TTEC or its SUPPLIERS), INCLUDING WITHOUT LIMITATION ANY LOST PROFITS, LOST DATA, LOST SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE, EVEN IF TTEC OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, NOR FOR THIRD PARTY CLAIMS. U.S. GOVERNMENT RESTRICTED RIGHTS: The Software is provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the U.S. Government is subject to restrictions set forth in subdivision (b)(3)(ii) or (c)(i)(ii)of the Rights in Technical Data and Computer Software Clause set forth in 252.227-7013, or 52.227-19 (c)(2) of the DOD FAR, as appropriate. Contractor/ Manufacturer is TOSHIBA TEC Corporation.
Wikipedia’s page for Toshiba
Publisher: www.toshiba.com