•
•
Insert hex bolts through top holes in jack stand
mounting brackets and holes in jack stand. Secure
with lock washers and hex nuts. See Figure 3.
Insert hex bolts through upper holes in the bottom
of mounting brackets and jack stand. Secure with
lock washers and hex nuts. See Figure 3.
•
Insert cotter pins through slots in nuts and holes in
axle and secure by bending the ends of the cotter
pins in opposite directions. See Figure 5.
Lock
Hex
Washer
Nut
Fender
Hitch Assembly
The hitch assembly is already attached to the tongue
before shipping. If not, follow instructions below:
Hex
Bolt
•
Remove the hardware from the hitch assembly and
place the hitch on the end of the tongue.
Insert hex bolt through flat washer, end of safety
chain, spacer, and then rear hitch hole. Pivot the
end of safety chain so it faces the ball end of hitch.
See Figure 4.
Reservoir
Tank
Flat
Washer
•
Flat
Washer
Hub Cap
Wheel
Hex Slotted
Cotter Pin
Nut
Figure 5
Lock
Nut
•
•
The wheels should spin freely and there should be
no side to side play.
Place hub caps in position on wheels and tap on to
the axle with a soft hammer or mallet.
Flat
Washer
Hex
Spacer Bolt
Hex
Bolt
IMPORTANT: Maximum tire pressure under any
circumstance is 30 psi. Equal tire pressure should be
maintained at all times.
Hitch
Assembly
Chain
Attaching Fenders
•
•
•
Remove the hex nuts, lock washers, flat washers,
and hex bolts from the side of tank.
Determine the proper assembly holes in the
fenders over the tires against the tank.
Insert hex bolts through flat washers, holes in
fenders, and tank. See Figure 5. Secure fender with
lock washers and hex nuts. Tighten securely.
Figure 4
•
•
Insert other spacer, safety chain, and flat washer
on the other end of the hex bolt and secure with hex
lock nut. See Figure 4.
Insert hex bolt through the front hole of hitch and
secure with flat washer and hex lock nut. Tighten
both hex nuts to 23 ft-lbs.
Attaching the Tongue
Attaching Wheels
•
•
•
Remove two hex bolts, lock washers, and hex nuts
on the front of the reservoir tank. See Figure 6.
Place the tongue in position and secure with
hardware just removed.
•
•
•
Block up the reservoir tank assembly about eight to
twelve inches.
Remove and discard plastic shipping caps on the
outside of the wheels.
Remove the cotter pin, hex slotted nut, and flat
washer from each axle.
Remove the reservoir tank from the blocks.
Reservoir
Tank
NOTE: It is recommended that you polish the axles with
emery cloth before you install the wheels.
Hex
Bolts
•
•
•
Place a wheel on each axle with the valve stem
facing outward. See Figure 5.
Place a flat washer on each axle and secure with
hex slotted nut.
Tighten slotted nut until snug and then back off
approximately 1/3 turn or until one of the slots on
the slotted nut lines up with the hole in the axle.
Tongue
Hex
Lock
Nuts
Washers
Figure 6
6
| Categories | Lawn Mower Manual, MTD Lawn Mower Manuals, Troy-Bilt Lawn Mower Manuals |
|---|---|
| Tags | MTD LS338, Troy-Bilt LS338 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | MTD, Lawn Mower |
| Document File Type | |
| Publisher | mtdproducts.com |
| Wikipedia's Page | MTD Products |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)
purchased a LS33TB from Lowe’s in Joplin. Received operator manual which stated engine manual was a separate item. However engine manual was not in pkg. Please advise as to how I may obtain engine manual. Thank you
Owen Johnson