MTD Cub Cadet 826 4×4 Snow Blower Owners Manual

WARNING:    Use    extreme   care    when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine   is   hot   or   running.   Extinguish
cigarettes, cigars, pipes an other sources
of ignition.
If you have a grounded three-prong receptacle,
proceed as follows:
Rotate choke knob to OFF position and do not
prime engine.
Connect power cord to switch box on engine. Plug
the other end of power cord into a three-hole,
grounded 120 volt AC receptacle.
Push starter button on top of the engine to crank
engine. As you crank the engine, move choke knob
to FULL choke position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
A plastic cup is provided inside the fuel fill opening
on the fuel tank. Remove and discard this cup
before filling up the tank. Use the separate fuel tank
cap to close after fill-up.
To Start Engine
When disconnecting the power cord, always unplug
from the three-prong receptacle first and then from
the snow thrower.
NOTE:  If  unit   shows  any  sign  of  motion   (drive  or
augers) with the clutch grips disengaged, shut engine
off  immediately.  Readjust  as  instructed  in  the  Final
Adjustments in the Assembly Section.
Recoil Starter
Attach spark plug wire to spark plug. Make certain
the metal loop on end of the spark plug wire (inside
the boot) is fastened securely over the metal tip on
the spark plug.
Rotate choke knob to FULL choke position (cold
engine start). If engine is warm, place choke in OFF
position instead of FULL.
Push primer button two or three times. If engine is
warm, push primer button once only.
Make certain the fuel shutoff valve is in the OPEN
(vertical position). See Figure 7.
Make certain the auger and drive control levers are
in the disengaged (released) position.
Move throttle control up to FAST position. Insert
ignition key into slot. See Figure 7. Be certain it
snaps into place. Do not turn key.
NOTE: Always cover vent hole in primer button    when
pushing. Additional priming may be necessary for first
start if temperature is below 15°F.
Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
NOTE:  Engine  will   not  start  unless  ignition   key  is
inserted into ignition slot in carburetor cover.
Electric Starter
Repeat the previous steps until engine starts.
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
If your house wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
To Stop Engine
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible freeze-up of starter,
proceed as follows.
Electric Starter:
WARNING:
The
electric
starter
is
Connect power cord to switch box on engine, then
equipped   with   a   grounded   three-wire
power cord and plug and is designed to
operate   on    120    volt   AC    household
current. It must be used with a properly
grounded  three-prong   receptacle  at  all
times  to  avoid  the  possibility  of  electric
shock.  Follow  all   instructions  carefully
prior to operating the electric starter.
to 120 volt AC receptacle. With the engine running,
push starter button and spin the starter for several
seconds. The unusual sound made by spinning the
starter will not harm engine or starter. Disconnect
the power cord from receptacle first, and then from
switch box.
Recoil Starter
With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud clattering
sound, which is not harmful to the engine or starter.
Move throttle control to stop or off position.
If your home electrical system is grounded, but a
three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
9
Product Specification
CategoriesCub Cadet Snow Blower Manuals, MTD Snow Blower Manuals, Snow Blower Manuals
Tags, ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 28 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Snow Blower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website