MTD White Outdoor 616 Hydrostatic Tractor Lawn Mower Owners Manual

6
Maintaining
Your Lawn
Tractor
Deck Wash System™ (If equipped)
Your tractor’s deck may be equipped with a water port on
its surface as part of its deck wash system. Use the  Deck
Wash System™ (sold separately) to rinse grass clippings
from the deck’s underside and prevent the buildup of cor-
rosive chemicals. Complete the following steps AFTER
EACH MOWING:
1.
Drive the tractor to a level, clear spot on your lawn,
near enough to a water sillcock (spigot)  for your
garden hose to reach.
IMPORTANT: Make certain the tractor’s discharge chute
is directed AWAY from your house, garage, parked cars,
etc.
2.
Disengage the PTO (Blade Engage),  move the shift
lever into the neutral position, set the parking brake,
and stop the engine.
Figure 6-
3
4
.  Thread the hose coupler (packaged  with your tractor’s
IMPORTANT: Make
certain the tractor’s
discharge chute is
directed AWAY from
your house, garage,
parked cars, etc.
On models with a 46-
inch deck, it may be
necessary to remove
the belt keepers from
around the engine pul-
ley, in order to remove
the PTO belt.
Operator’s Manual) onto the end of your garden hose.
.  Attach the hose coupler  to the water port on your
decks surface. See Figure 6-2.
Hairpin Clip
5.
6
Turn the water on.
Spring
.  While sitting in the operator’s  position on the tractor,
re-start the engine and place the  throttle lever in the
FAST (rabbit) position.
7.
8.
Disengage the parking brake.
Moveposition.the tractor’s PTO (Blade Engage) into the ON
PTO Cable
9.
Remain in the operator’s position with  the cutting
deck engaged for a minimum of two minutes, allowing
the underside of the cutting deck  to thoroughly rinse.
10.
11.
12.
13.
Moveposition.the tractor’s PTO (Blade Engage) into the OFF
Turn the ignition key to the STOP position to turn the
This Operators Man-
ual covers a range of
product specifications
for various models.
Characteristics and
features discussed
and/or illustrated in
this manual may not
be applicable to all
models. MTD LLC
Figure 6-3
tractor’s engine off and engage the parking brake.
Turn the water off and detach the hose coupler from
the water port on your decks surface.
Repeat steps 4-11 on the opposite side of the cutting
deck.
Cutting Deck Removal
To remove the cutting deck, proceed as follows:
1.
Place the PTO (Blade Engage) knob (or  lever) in the
disengaged (OFF) position and engage  the parking
brake.
reserves the right to
change product speci-
fications, designs, and
equipment without
notice and without
incurring obligation.
2.
3.
Lower the deck by moving the deck lift lever into the
Support Pin
bottom notch on the right fender.
Remove the hairpin clip that secures the PTO cable to
the rear of the cutting deck. See Figure 6-3.  Remove
the PTO cable and accompanying spring from the
cutting deck.
4.
Remove the deck belt from around the tractor’s
engine pulley (or electric PTO clutch, if so equipped).
Figure 6-4
3
Product Specification
CategoriesLawn Mower Manual, MTD Lawn Mower Manuals, White Outdoor Lawn Mower Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 64 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandMTD, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishermtdproducts.com
Wikipedia's PageMTD Products
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website